Description
Build transmissions with gears, pulleys, belts and chains, and connect a motor. See how the rotation frequency and the direction of rotation change from one piece to the next: what you gain in speed you lose in force (torque).
Physical model
Meshing gears have the same rim speed (v = ω·R) and turn in opposite directions: ω₂ = −ω₁·R₁/R₂. A belt and a chain also carry the same rim speed, without reversing the direction (a crossed belt reverses it). Pieces on the same shaft have the same ω. All gears have teeth of the same size, so the number of teeth is proportional to the radius (here, 10 teeth per centimeter). If a loop of pieces required two different rotations for the same piece, the system locks. The rotations are calculated at each step through the network of connections, starting from the motor.
Simplifications
Here the chain connects gears. In reality, the chain runs over its own toothed wheels (a bicycle’s chainring and sprocket), with teeth of the same pitch as the links; ordinary gears have teeth made to fit into other gears. For the physics of the transmission it makes no difference: the chain carries the same speed from one rim to the other.
Description
Pull a block up a ramp with a rope parallel to the ramp and compare the force on the spring scale with the weight of the block. Change the height h and the length L of the ramp: the gentler the ramp, the smaller the force, but the greater the length of rope pulled to rise the same height. In the Friction panel, add static and kinetic friction between the block and the ramp.
Physical model
Ideal rope (massless and inextensible), parallel to the ramp. The rope is pulled slowly, at constant speed, so the force on the spring scale is the equilibrium force. Without friction, F = P·sin θ = P·h/L, the part of the weight along the ramp (the other part, P·cos θ, is balanced by the normal force N of the ramp). The mechanical advantage is MA = L/h. To rise a height h, the block is pulled a distance L along the ramp, and the work of the force F (F × L) equals that of lifting the block vertically (P × h). With friction, going up, F = P·sin θ + μc·N; going down, F = P·sin θ − μc·N; the work of F exceeds P × h, and the difference becomes heat. At rest, static friction is whatever it takes, up to μe·N: a force F = P·sin θ − μe·N is enough (if this is negative, friction holds the block by itself and the rope goes slack). For the block to start rising, the force must overcome the maximum static friction, F = P·sin θ + μe·N; once it slides, the force drops to that of kinetic friction.
Simplifications
Friction follows the textbook model: constant coefficients that do not depend on speed or contact area. At rest, the spring scale reads only the minimum force needed to hold the block. The rope is always pulled slowly: at start-up and when stopping, the force would be slightly different from P·sin θ for a moment (Newton’s 2nd law). The length L is that of the whole ramp; the block, which has a size, stops when its front reaches the top.
Description
Lift a load with pulleys: a fixed pulley, an exponential arrangement of movable pulleys, or a block and tackle. Pull the rope with the spring scale and compare the force with the weight of the load, and how much rope was pulled with how much the load rose: what you gain in force you lose in distance.
Physical model
Ideal ropes and pulleys: massless, frictionless and inextensible. The tension is the same along a rope, and each movable pulley is in equilibrium under the forces of the ropes that hold it. The rope is pulled slowly, at constant speed, so the force on the spring scale is the equilibrium force: F = P/MA, with MA = 1 for the fixed pulley, 2ⁿ for the exponential arrangement (n movable pulleys) and N for the block and tackle (N rope segments holding the load). Since the length of the ropes does not change, you pull MA times more rope than the load rises, and the work of the force F (F × rope pulled) equals the energy gained by the load (P × height). The fixed pulley only changes the direction of the force: the angle θ of the rope with the vertical does not change F.
Simplifications
In the block and tackle, the pulleys are drawn side by side so that all the rope segments are vertical. In real block and tackles, the upper pulleys share one axle (in a single block), and so do the lower ones; the force is the same. The pulleys have no mass: with heavy pulleys, the force would also have to lift the movable pulleys.
Description
Build a lever (seesaw) by dragging the fulcrum, the blocks, the people and the hand along the bar. Choose the force of the hand and find out which way the bar turns, or which force balances it; blocks can be stacked. The simulator identifies the class of the lever by itself (first, second or third class).
Physical model
Rigid 4 m bar resting on a point, with forces always vertical (weights P = m·g and the force of the hand). At equilibrium, the sum of the moments about the fulcrum is zero: P₁·d₁ + P₂·d₂ + … = F·d. Out of equilibrium, the bar rotates about the fulcrum according to I·α = Στ (with slight damping) until one of its ends touches the ground. Since all the forces are vertical, the moments all vary with the same cos θ: a balanced bar would stay at rest at any inclination. To show that it is balanced, when you start it rocks slowly, with a small amplitude (a visual cue, not a result of the dynamics).
Developers
Marco P. M. de Souza
References
HEWITT, P. G. Conceptual physics. 12th ed. Porto Alegre: Bookman, 2015.
HALLIDAY, D.; RESNICK, R.; WALKER, J. Fundamentals of physics, vol. 1: mechanics. 10th ed. Rio de Janeiro: LTC, 2016.